Common Repairs And Replacing Things To Remember About Toilet parts
Replacing the major toilet parts is easily accomplished as follows:
If you hear sounds of dripping water when you are near the toilet, it is usually because the flush valve, sometimes referred to as flapper valve, is leaking allowing water to leave the tank. When the tank water gets to a certain level, the fill valve will open, allowing water to re-enter the tank. You may have heard the tank refilling after hearing the dripping sound. With these signs, you can be certain the flush valve needs replacing. Replacing the valve is very easy if you follow the directions I am going to give you below. Don’t be concerned about your hands being in the remaining water in the tank. It is completely fresh water.
How To Replace Toilet Flush Valve
1. Remove the toilet tank lid
2. Turn off water
Turn off the water supply valve located at the wall below the left side of the toilet tank. Turn the valve completely clockwise. Now hold down the flush lever until most of the water leaves the tank.
3. Disconnection chain from flush handle lever
Remove the chain that connects between the flush handle lever and the flush valve. The chain is usually attached with a clip to the flush lever. Open the clip and remove the chain.
4. Remove flush valve from bottom of tank
Reach your hand down to the valve and remove the two attaching ears holding the valve to the overflow tube. Remove the valve from the tank.
5. Clean surface of valve seat.
With a rag, clean the ring seat where the flush valve was located.
6. Install the new valve
Install the new valve by attaching the two ears to the two retaining tabs.
7. Attach the chain
Attach the chain clip to the flush lever leaving a little slack in the chain.
8. Turn on water
After the tank fills, flush the toilet. Did the valve open completely during the flush and close after the flush? If not, readjust the chain length at the flush handle lever.
9. Replace tank lid
How To Replace Toilet Fill Valve
If you notice that you can still hear water running in the toilet tank after having replaced the flapper valve, the water fill valve either needs adjusting or replacing. Try adjusting the valve with the adjusting device on the valve assembly. If you still have a problem after the adjustment, you will have to replace the valve. There are various types of fill valves. The removal and installation procedure is the same for all types .
1. Remove tank lid
2. Turn off water supply
Turn off the water supply valve located at the wall below the left side of the toilet tank. Turn the valve completely clockwise. Now hold down the flush lever until most of the water leaves the tank.
3. Remove the water supply line from the fill valve shaft
Prior to removing the supply line, place a container under the toilet tank to catch any water remaining in the tank. Next, unscrew the hex nut on the supply line where attached at the bottom of the tank.
4. Loosen and remove fill valve shaft nut
The shaft nut is located on the bottom exterior of the tank at the water supply line.
5. Lift out valve
Grasp the valve at the inside of the tank and lift out.
6. Install new fill valve
Make sure the rubber seal is on the bottom of the valve shaft. Insert the fill valve in the opening in the tank and secure it with the fastening nut. Tighten the nut finger tight with an additional quarter turn with the channel locks.
7. Re-attach water supply line
8. Turn on water
9. Adjust water level
Follow the instructions that came with the new fill valve for making the proper adjustment.
10. Replace tank lid
If all the above steps on how to replace toilet flush and fill valves are followed, your toilet will be operating like new again.
I have been inspired by this article. It's thought-provoking, fascinating and worthy of a positive comment. I appreciate that you worked hard to make this information interesting and clear. This content is superb and deserves a top rating.
ReplyDeletePipe relining Sydney
your ideas helpful for us, your post very good, nice article. If you want to write for us home.. Than visit my website Write for us Home Improvement
ReplyDeleteYukinova is a Two Wheeler Battery Manufacturers in India. These products are highly demanded and appreciated by a number of clients owing to their optimum performance, hassle free working and longer functional life. Offered products are designed and fabricated by considering optimum quality components in accordance with the laid industry standards and norms. Moreover, our clients can avail these products Three Wheeler Battery, Traction Battery, Solar Battery from us at best price.
ReplyDelete
ReplyDeleteOwning a home solar system is like having the coolest mom around: you get to be totally green and save money, too
The solar system for home is a great way to reduce your carbon footprint without compromising the quality of your living environment
Solar System For Home